• CarbonDoser electronic CO₂ regulator.  learn about it here 
• Milwaukee monitor/controller (SMS122) learn more
• INT500 or upgrade to optional External Reactor 5000 
• 10' CO₂ resistant tubing
• 1 bottle 7.01 calibration solution:
• "THE BEST" Check Valve

When injecting CO2 into a planted tank, it is useful to know how much CO2 is actually getting dissolved into the water. Lucky for us, there is a simple way to calculate the CO2 level, based on the pH, and KH of the tank water. There is a fixed relationship between the pH, KH, and CO2 level. As you increase the amount of CO2 that is dissolved into the water, the pH will drop. And if you then stop adding CO2, the pH will climb as that extra CO2 is released from the water.

A little background science:
pH is a measure of the concentration of hydrogen ions [H+] in solution. pH is actually a logarithmic measure (-log[H+]). This formula has two implications. First, it means that the hydrogen ion concentration increases (thus the solution becomes more acidic) as the pH number decreases. Second, each time the pH is reduced by 1, the concentration of hydrogen ions increases by a factor of 10.

In more simple terms, the pH is simply a measure of the acidity or alkalinity of a solution. pH values from 0 to 7 are considered acids, and pH values from 7-14 are considered bases. 7 is neutral, neither an acid nor base.

As we add CO2 to water, it forms carbonic acid, which lowers the pH. The more CO2 that gets dissolved into the water, the lower the pH.

Working to raise the pH of the water is the KH. While KH refers to Carbonate Hardness, what is really measured by a standard KH test kit is really the buffering capacity. In "most" water sources, the buffering is provided by Carbonate. In that case, buffering capacity and KH are the same thing. Assuming a constant amount of CO2, a higher KH, will result in a higher pH.

Many people are under the mistaken impression that a low KH results in large pH swings when adding CO2, while raising the KH will result in smaller pH swings. This is not the case. The KH will move the start and end pH values, but the pH swing will be the same for a given level of CO2. You can see this in the chart below, or using the calculation:

One possible explanation for this myth is that many copies of this pH chart skip some of the higher pH values, for example, jumping from pH 7.4 to a pH of 8.0. If the reader didn't pay careful attention, they might mis-interpret the size of the pH swing. I specifically made sure to include all pH values, between 6 and 8, in steps of .2.

This relationship will break down at extremely low KH levels (below 1 degree), when there isn't enough carbonate to completely buffer the acids present. In that case, the pH can drop quickly and dramatically. But if the KH is 1 degree or higher, then the size of the pH swing when injecting CO2 will be determined only by the amount of CO2 dissolved in the water.

The pH-KH-CO2 Relationship
pH, KH, and CO2 have a fixed relationship as long as carbonate is the only buffer present (no phosphate buffers like pH-UP and- DOWN, Discus Buffer, etc). There are some parts of the country that have high levels of phosphates in their water supply. For those cases, determining CO2 levels will be difficult, as the phosphate will throw off the pH-KH-CO2 relationship, which means the CO2 charts and calculator below won't work. Note that the commercially available CO2 test kits will also be invalidated by the phosphates.

To determine your CO2 level based on the pH and KH, you can enter the values into the on-line calculator, or use the chart at the bottom of the page.

NOTE: If you aren't adding CO2 to your water, and the CO2 level based on the pH and KH indicates more than 5ppm, then it is very likely that some other buffer (such as phosphate) is present in your water. In an inhabited aquarium, the amount of CO2 produced by the fish will not have an effect on CO2 levels in the water. Any excess CO2 created by fish will dissipate into the air, leaving a fairly constant CO2 level of about 3-4ppm. If you test your pH and KH, and without adding any CO2, the chart says you've got 20ppm CO2, don't believe it.

In some case, water coming right from the tap can contain very high or very low levels of CO2. This can result in tap water with a high KH, and low pH. But, in just a few hours, that excess CO2 will dissipate from the water, leaving the normal 3-4ppm, and the pH will rise. Sometimes, the water might come from the tap with extremely little CO2, which can result in tap water with a low KH, and a very high pH. Again, after a few hours, the CO2 level will equalize, and the water will end up with 3-4ppm CO2.

CO2/pH/KH calculator and chart

If you have measured your pH and KH, and want to know how much CO2 you have, enter the pH and KH here.

The formula used for this calculation is: CO2 (in PPM) = 3 * KH * 10^{( 7-pH )} where KH is Carbonate Hardness in degrees.

This is a common misconception when using the CO2 / KH / pH table. It appears that by altering any parameter, the other values should move. But this is not true. Treat the pH value you see as a result. If you alter the KH, then the pH will move. If you alter the CO2 level, then the pH will move. The pH will always react to changes in either of the other two parameters.

You can not alter the KH levels other than by adding or removing carbonate. You can not alter the CO2 levels other than by adding or removing CO2.

Adding certain "pH altering additives" can cause much confusion as well. Additives like "Proper pH 7.0" which force the pH to a certain value completely invalidate the CO2 / KH / pH relationship. This is because these pH altering additives contain phosphates. Phosphates replace the carbonates in the buffering system. And the CO2 / KH / pH relationship is only valid in a system that is buffered by Carbonates.

There is on case I've seen where the addition of CO2 resulted in an increase in KH. This can happen when you have something in the tank that dissolves carbonate into the water. Seashells, crushed coral, and many gravels and rocks will do this. With the addition of CO2, the water turns more acidic, which will increase the dissolving of the minerals. It appears that increasing CO2 raises the KH, which isn't really the case. The dissolving minerals raise the KH, and the increase in KH results in an increase in pH. In a system using a pH probe and controller to regulate CO2 levels, this can have fatal consequences, since the pH controller will keep trying to lower the pH, but as more CO2 is dissolved, it lowers the pH, which raises the KH, which raises the pH. So you now have more CO2, but the same pH. So the controller adds even MORE co2. And it will keep going. So it's important to know your KH whenever using pH to judge CO2 levels.

The formula listed above (used in the on-line calculator) was used to create the chart shown below.